Sharp IQ-8000 Manual de instalación Pagina 106
- Pagina / 125
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
9.4 IQ 8-Reader Expansion Module (P/N: 03-10102-201E)
The IQ-400 4-reader system can be expanded to a 12-reader system by installing the 8-Reader
Expansion Module. The 8-Reader Expansion board can be mounted below the IQ-400 in the larger
enclosures available from PCSC. Once mounted, the 8-Reader Expansion board is connected to the
IQ-400 by installing a 50-pin ribbon expansion cable from P1 on the 8-reader Expansion board to J1 on
the IQ-400. The 8-Reader expansion board allows the user to connect up to 8 additional readers to the
IQ-400. Each of the reader interfaces support either a PCSC proprietary reader (4-wire interface), or a
Wiegand reader (5-wire interface). The Expansion board also provides 8 additional interfaces for each of
the readers and the associated doors. These include the following:
•
Multilevel Door Sense Inputs (Supervised door sense inputs)
•
Reader Present inputs (Reader connected/disconnected)
•
Request to Exit inputs (Supervised Egress Inputs)
•
Relay contacts for door control outputs (Form C dry contacts rated for 2.0 Amps @ 12/24VDC
continuous power)
•
Door shunt/Local Alarm/Outputs (Open Collector output rated for +12 VDC @ 100mA)
9.4.1 Electrical Ratings
Power: 12VDC
Draw: 160mA @ 12V
Relay Contacts 2 A @ 24 VDC
Data0/Data1 5 Vdc @ 0 mA for Logic 1
0 Vdc @ 5mA for Logic 0
Card Reader Draw: 100mA @ 12 VDC
Alarm Point Voltage 5.0 Vdc @ 0.0 mA when Sense Input is in Open Circuit Physical State.
& Tamper Voltage 0.0 Vdc @ 5.0 mA when Sense Input is in Short Circuit Physical State.
1.6 Vdc @ 3.4 mA when Sense Input is in Alarm Physical State.
0.9 Vdc @ 4.1 mA when Sense Input is in Normal Physical State.
9.4.2 Power Supply
The 8-reader Expansion Module requires +5VDC for all logic. Relays, output drivers, etc. require a
+12VDC supply. The +5VDC and +12VDC is provided to the module via the 50-pin expansion cable,
which connects plug P1 of the 8-door cluster PCB (P/N 03-10102-201E) to plug J1 of the IQ-400 board,
(P/N 03-10111-201). The Variable Ambient Test will be for Indoor, 0 to 49 Degrees C, and 85% Relative
Humidity @ 30 Degrees C.
Page xciii of 110 IQ-400 Installation Manual 33-10057-001-C
- Installation Manual 1
- 33-10057-001 1
- 0.1 Board Diagrams 3
- 0.1.4 OUT Expansion Board 6
- 0.1.5 ALM Expansion Board 7
- 0.1.6 SAM Board 8
- 0.2 Table of Contents 9
- 1.0 Introduction 14
- 2.0 Unpacking the IQ-400 16
- IQ-400 - Expansion Cable Plug 19
- 3.0 Installing Power 20
- 4.0 Wiring Your Readers 24
- 4.3.1 Procedure 25
- 4.4.1 Procedure 28
- 4.4.2.1 Procedure 28
- 5.0 Reader Connections 29
- Option 1 34
- Option 2 35
- – Option 2 37
- IQ-400 Board 38
- Expansion Board 39
- 6.0 Wiring the Door(s) 46
- 6.6.3 SAM Board LED Arrays 56
- Exit Sense Inputs 59
- 6.10.1 Procedure 61
- 7.1 Reset the IQ-400 Panel 62
- 7.5 Changing the Baud Rate 69
- PCSC P/N: 04-10318-101 73
- PCSC P/N: 04-10318-001 73
- HyperTerminal 76
- Protocol) 77
- 7.10.2 Installation 78
- 7.10.3 Optical Transmission 80
- 8.1 Status Lights 81
- 8.2 Communication Errors 82
- 8.2.2 Error Codes 83
- (Pins 2-3) 86
- 8.8 User Selectable Options 91
- 8.9 Point Definitions 93
- 8.9.1 Sense Inputs 93
- S3 through S6 are 94
- IQ 4 PCB 94
- 8.9.2 Outputs 96
- Connector 96
- 9.1 IQ-400 Features 99
- 9.1.3 Spare Parts- IQ-400 PCB 100
- 9.2.1 Electrical Ratings 101
- 9.2.2 Power Supply 101
- 9.2.3 Door Sense LEDs 102
- 9.2.5 Jumpers 102
- 9.3.2 System Capacities 104
- 9.3.3 Electrical Ratings 104
- 9.4.1 Electrical Ratings 106
- 9.4.2 Power Supply 106
- 9.4.3 Door Sense LEDs 107
- 9.4.5 Jumpers 107
- 9.5.1 System Capacities 109
- 9.5.2 Electrical Ratings 109
- 9.6.1 System Capacities 111
- 9.6.2 Electrical Ratings 111
- 9.6.3 Spare Parts- OUT PCB 111
- 9.7.1 System Capacities 112
- 9.7.2 Electrical Ratings 112
- 9.8 SAM Board 113
- 4-wire PCSC 114
- 5-wire Wiegand 114
- 9.10 Tool Requirements 115
- 10.1.1 Required Equipment: 118
- 10.1.2 Required Information: 118
- 10.1.3 Required firmware: 118
- 10.3.1 TCP/IP Configuration 121
- 10.4 Resetting the IQ-400E 124
- End of Manual 125
- PCSC, Inc 125
- August 2008 125
Relacionado con productos y manuales para Los Componentes Del Dispositivo De Seguridad Sharp IQ-8000
(14 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales