Sharp IQ-8000 Manual de instalación Pagina 77
- Pagina / 125
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
7.10 PC Host to IQ-400 Communication Using Fiber Optics (RS-485
Protocol)
PCSC has tested two fiber optics systems for communication between the PC host and the IQ
panels. Both were found to be acceptable and compatible with the IQ-400. It is recommended
that other systems available on the market should be equivalent to the specifications inherent in
the two products tested. PCSC does not endorse or specify either of these 2 systems. Any
communication links beyond the normal wiring of the IQ system is the responsibility of the fiber
optics company and the installer. Refer to the installation instructions of the fiber optics system
you are using. The information listed below is a general description of how one supplier,
American Fibertek, communicates via fiber optics data links, to the PC host and the IQ panel.
7.10.1 Product Description
The MX-485-2 is a remote mountable module that converts two-wire RS-485 data signals into
modulated light for coupling into fiber optic cables. The unit transmits and receives high and low
logic level data and the HiZ bus state through duplex fiber optic cables. Any EIA RS-485 protocol
signals up to 19.2 Kbaud may be transmitted over fiber optics cable by using two 485-2 series
units. Designed primarily to be used with inexpensive 50u fiber cable, the 485-2 series may also
be used with 62.5u fiber.
7.10.1.1 Connector
The signal and power connector is a seven position detachable terminal block. The connections
should be made as shown on the wiring diagram before power is applied. ST optical connectors
are standard on the unit.
7.10.1.2 Power Supply
Power required is 12VDC @ 200mA maximum. Internal regulators are included so unregulated
12 volt power may be used. The case of the unit is connected to signal ground.
7.10.1.3 Controls and Indicators
There are no controls on the MX-485-2 and three indicators. The ON indicator will glow green
when power is applied to the unit. The TX and RX LEDs glow red to show activity on the data
wires. The TX LED indicates the fiber modem is transmitting and the RX LED indicates reception
of data.
Page lxiv of 110 IQ-400 Installation Manual 33-10057-001-C
- Installation Manual 1
- 33-10057-001 1
- 0.1 Board Diagrams 3
- 0.1.4 OUT Expansion Board 6
- 0.1.5 ALM Expansion Board 7
- 0.1.6 SAM Board 8
- 0.2 Table of Contents 9
- 1.0 Introduction 14
- 2.0 Unpacking the IQ-400 16
- IQ-400 - Expansion Cable Plug 19
- 3.0 Installing Power 20
- 4.0 Wiring Your Readers 24
- 4.3.1 Procedure 25
- 4.4.1 Procedure 28
- 4.4.2.1 Procedure 28
- 5.0 Reader Connections 29
- Option 1 34
- Option 2 35
- – Option 2 37
- IQ-400 Board 38
- Expansion Board 39
- 6.0 Wiring the Door(s) 46
- 6.6.3 SAM Board LED Arrays 56
- Exit Sense Inputs 59
- 6.10.1 Procedure 61
- 7.1 Reset the IQ-400 Panel 62
- 7.5 Changing the Baud Rate 69
- PCSC P/N: 04-10318-101 73
- PCSC P/N: 04-10318-001 73
- HyperTerminal 76
- Protocol) 77
- 7.10.2 Installation 78
- 7.10.3 Optical Transmission 80
- 8.1 Status Lights 81
- 8.2 Communication Errors 82
- 8.2.2 Error Codes 83
- (Pins 2-3) 86
- 8.8 User Selectable Options 91
- 8.9 Point Definitions 93
- 8.9.1 Sense Inputs 93
- S3 through S6 are 94
- IQ 4 PCB 94
- 8.9.2 Outputs 96
- Connector 96
- 9.1 IQ-400 Features 99
- 9.1.3 Spare Parts- IQ-400 PCB 100
- 9.2.1 Electrical Ratings 101
- 9.2.2 Power Supply 101
- 9.2.3 Door Sense LEDs 102
- 9.2.5 Jumpers 102
- 9.3.2 System Capacities 104
- 9.3.3 Electrical Ratings 104
- 9.4.1 Electrical Ratings 106
- 9.4.2 Power Supply 106
- 9.4.3 Door Sense LEDs 107
- 9.4.5 Jumpers 107
- 9.5.1 System Capacities 109
- 9.5.2 Electrical Ratings 109
- 9.6.1 System Capacities 111
- 9.6.2 Electrical Ratings 111
- 9.6.3 Spare Parts- OUT PCB 111
- 9.7.1 System Capacities 112
- 9.7.2 Electrical Ratings 112
- 9.8 SAM Board 113
- 4-wire PCSC 114
- 5-wire Wiegand 114
- 9.10 Tool Requirements 115
- 10.1.1 Required Equipment: 118
- 10.1.2 Required Information: 118
- 10.1.3 Required firmware: 118
- 10.3.1 TCP/IP Configuration 121
- 10.4 Resetting the IQ-400E 124
- End of Manual 125
- PCSC, Inc 125
- August 2008 125
Relacionado con productos y manuales para Los Componentes Del Dispositivo De Seguridad Sharp IQ-8000
(14 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales