Sharp YO-370 Manual Pagina 19
- Pagina / 118
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
FTS 370d/w/r Revision 10 – 1/09/2015 7
Table 1-3 – Status & Alarm LEDs
Note: See Table 3-3 for a complete list of alarms provided by the information display.
LED
Indication
DAY ALARM
Red to indicate one or more of the following conditions:
1. The connected beacon is experiencing a failure in Day mode.
2. The beacon is not communicating with the SC 370. The Day Alarm will
be accompanied by the Night Alarm and the Comm. Alarm in this instance.
NIGHT ALARM
Red to indicate one or more of the following conditions:
1. The connected beacon is experiencing a failure in Night mode.
2. The beacon is not communicating with the SC 370. The Night Alarm
will be accompanied by the Day Alarm and the Comm. Alarm in this
instance.
3. Beacon IR failure. Activation of Night Alarm due to IR failure requires
that “IR Enable” and “IR Alarm Is Night Alarm” are set to “Yes”. See
Section 3 “Site Tower Config.” for additional information.
MARKER ALARM
Red to indicate one or more of the following conditions:
1. One or more L-810 markers have failed.(FTS 370d L-864/865 only)
2. The marker interface board is not communicating with the SC 370.
The Marker Alarm will be accompanied by the Comm. Alarm in this
instance.
PHOTODIODE
Red when more than 19 hours have passed since the system has
changed modes via the photodiode input.
COMM ALARM
Red to indicate a communications failure in one or more of the following
conditions:
1. One or more connected units (Systems 2 – 6) are not communicating
with System 1.
2. The connected beacon is not communicating with the SC 370. The
Comm. Alarm will be accompanied by the Day Alarm and Night Alarm.
3. The connected marker tier is not communicating with the SC 370. The
Comm. Alarm will be accompanied by the Marker Alarm.
GPS SYNC
More than one hour has passed since the unit received a GPS Sync.
pulse.
DAY MODE
Green continuous when unit is in DAY mode, blinking when the unit is in
manual DAY mode.
RED NIGHT
Green continuous when unit is in RED NIGHT mode, blinking when the
unit is in manual RED NIGHT mode.
WHITE NIGHT
Green continuous when unit is in WHITE NIGHT mode, blinking when the
unit is in manual WHITE NIGHT mode.
485 TX Red blinking when the unit is sending data to other units in the system.
485 RX Red blinking when the unit is receiving data from other units in the system.
FLASH
Active only if GPS is enabled. Blinks approximately once per minute when
SAT lock is achieved.
- VANGUARD 1
- FTS 370d, 370w, 370r 1
- System Controller (SC) 370 5
- Flashhead CABLE 5
- Front Matter 7
- Personnel Hazard Warning 8
- Table of Contents 9
- List of Figures 11
- List of Tables 12
- System Overview 13
- Specifications 14
- Operation Overview 16
- PCB1 Controller Board 17
- Manual Override 18
- Status and Alarm LEDs 18
- P2 Auxiliary Input 21
- J4 Communication Cable 21
- Connection 21
- PCB3 Smart Board 22
- GPS Sync. Kit 22
- USB Port 22
- FH 370d/w/r 23
- Controller Installation 26
- Input Power 27
- Photodiode Wiring 27
- Photodiode Mounting 27
- Cellular Antenna 28
- GPS Antenna 29
- Communication Cable Kit 31
- Dry Contact Alarm Outputs 33
- Flashhead Cable 33
- Wiring Procedure 33
- Securing the Cable 34
- Flashhead Installation 37
- DETAIL A 40
- 15.75 (400) 43
- 7.5 (190.5) 43
- KNOCKOUT SIZE DIA 45
- PHOTODIODE 50
- INTERFACE BOX 52
- Standard System 56
- LOW BATT 64
- MARKER INTERFACE 66
- (P/N 2422000) 66
- (P/N 1362034) 66
- The photodiode 68
- Marker Mode 68
- Red Flash Mode 68
- IR Enable 70
- IR Is Night Alarm 70
- Local Tower Config 72
- Local Ethernet Configuration 74
- Primary Data Monitoring 74
- Alternate Data Monitoring 74
- Site Event History 76
- Lighting Inspection (LI) 78
- Mode Override 79
- System Reboot 79
- System X Firmware 79
- USB Firmware Update 80
- Information Display Alarms 80
- Section 4– Web Interface 82
- Auto Fast LI 83
- Manual Fast LI 83
- Manual Staged LI 83
- Auxiliary Input 84
- Tower Lighting 85
- System “X” 86
- Monitoring 87
- SNMP Labels 87
- Cellular Modem 88
- Troubleshooting 90
- Component Removal and 93
- Replacement 93
- EHTERNET 98
- 1 2 3 4 5 98
- Table 6-4 – Marker Interface 100
- Critical 102
- Table A-1 – Critical INFORMs 103
- Table A-2 – Warning INFORMs 104
- Modbus RTU over RS485 106
- Modbus RTU over TCP 106
- Implemented Modbus Map 106
- RMA Policy Revision 2014B 117
- Revision 2014B RMA Policy 118
© 2020, manymanuals.es. Todos los derechos reservados | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales