Sharp YO-370 Manual Pagina 102
- Pagina / 118
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
90 Revision 10 – 1/09/2015 FTS 370d/w/r
Appendix A: Vanguard (v3.1) SNMP V2c INFORM TRAPs
Vanguard supports SNMP V2c INFORM TRAPs to notify SNMP managers of field
events. Any INFORM that is not acknowledged within 20 minutes will be resent every 20
minutes until it is acknowledged; up to 24 hours. SNMP TRAPs do not require
acknowledgement. This document describes the default severities for INFORMs. The
severity setting and name for all INFORMs is configurable via the Vanguard web interface or
SNMP sets.
Vanguard SNMP INFORM TRAPs Default Severities
Critical
INFORMs, whose default severity setting is set to Critical, are those which indicate a
NOTAM worthy event. The set of Critical INFORMs would be the minimum set required to
handle to ensure proper monitoring.
See Table A-1 for a list of Critical INFORMs and their descriptions.
Warning
INFORMs, whose default severity setting is set to Warning, are those which indicate
maintenance is needed on a component of the lighting system, but would not necessarily
require a NOTAM. In some situations these INFORMs may be as important as the Critical
events and in others they may not.
See Table A-2 for a list of Warning INFORMs and their descriptions.
Info
INFORMs, whose default severity setting is set to ‘Info’, do not indicate NOTAM worthy
events; although some of them may accompany the Critical INFORMs as additional
diagnostic information.
See Table A-3 for a list of Informational INFORMs and their descriptions.
- VANGUARD 1
- FTS 370d, 370w, 370r 1
- System Controller (SC) 370 5
- Flashhead CABLE 5
- Front Matter 7
- Personnel Hazard Warning 8
- Table of Contents 9
- List of Figures 11
- List of Tables 12
- System Overview 13
- Specifications 14
- Operation Overview 16
- PCB1 Controller Board 17
- Manual Override 18
- Status and Alarm LEDs 18
- P2 Auxiliary Input 21
- J4 Communication Cable 21
- Connection 21
- PCB3 Smart Board 22
- GPS Sync. Kit 22
- USB Port 22
- FH 370d/w/r 23
- Controller Installation 26
- Input Power 27
- Photodiode Wiring 27
- Photodiode Mounting 27
- Cellular Antenna 28
- GPS Antenna 29
- Communication Cable Kit 31
- Dry Contact Alarm Outputs 33
- Flashhead Cable 33
- Wiring Procedure 33
- Securing the Cable 34
- Flashhead Installation 37
- DETAIL A 40
- 15.75 (400) 43
- 7.5 (190.5) 43
- KNOCKOUT SIZE DIA 45
- PHOTODIODE 50
- INTERFACE BOX 52
- Standard System 56
- LOW BATT 64
- MARKER INTERFACE 66
- (P/N 2422000) 66
- (P/N 1362034) 66
- The photodiode 68
- Marker Mode 68
- Red Flash Mode 68
- IR Enable 70
- IR Is Night Alarm 70
- Local Tower Config 72
- Local Ethernet Configuration 74
- Primary Data Monitoring 74
- Alternate Data Monitoring 74
- Site Event History 76
- Lighting Inspection (LI) 78
- Mode Override 79
- System Reboot 79
- System X Firmware 79
- USB Firmware Update 80
- Information Display Alarms 80
- Section 4– Web Interface 82
- Auto Fast LI 83
- Manual Fast LI 83
- Manual Staged LI 83
- Auxiliary Input 84
- Tower Lighting 85
- System “X” 86
- Monitoring 87
- SNMP Labels 87
- Cellular Modem 88
- Troubleshooting 90
- Component Removal and 93
- Replacement 93
- EHTERNET 98
- 1 2 3 4 5 98
- Table 6-4 – Marker Interface 100
- Critical 102
- Table A-1 – Critical INFORMs 103
- Table A-2 – Warning INFORMs 104
- Modbus RTU over RS485 106
- Modbus RTU over TCP 106
- Implemented Modbus Map 106
- RMA Policy Revision 2014B 117
- Revision 2014B RMA Policy 118
GE JBW3-4 manuels
Manuels d'utilisation et guides de l'utilisateur pour Cuisiniers GE JBW3-4.
Nous fournissons des manuels en pdf 1 GE JBW3-4 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentarios a estos manuales