Sharp JW-20CM Manual de usuario Pagina 172
- Pagina / 230
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
10·4
10
10-4 Command
For communication format etc., see network module ZW-98CM/ZW-20AX etc. instruction manual of
host computer side.
Read out relay (1 point unit)
Function Read out ON (01
(H)
)/OFF (00
(H)
) status of specified relay.
Command code 00
(H)
(MRL)
Writing mode assignment No
Operation condition of PC Unrelated
Assignable address 00000 to 15777
(8)
Set/reset relay (1 point unit)
Function Set (01
(H)
)/reset (00
(H)
) the specified relay.
Command code 10
(H)
(SRR)
Writing mode assignment No
Operation condition of PC Unrelated
Assignable address 00000 to 15777
(8)
· "Writing mode assignment" is used to show whether writing to the PC memory has been enabled or
disabled.
0: Writing prohibited
1: Enable writing only to data memory
2: Enable writing all data.
No setting: Enable writing in any mode
Letters in brackets are
command name of BASIC
mode.
Letters in brackets are
command name of BASIC
mode.
- Version 2.2 1
- Produced in Oct. 1997 1
- Safety Precautions 3
- Caution 4
- Prohibit 4
- Network module JW-20CM 6
- - User’s Manual 6
- Table of contents 7
- Chapter 1 Outline 9
- Chapter 2 Safety Precautions 10
- Joint using a 11
- 2-3 Treatment 12
- 2-4 Static electricity 12
- 2-5 Maintenance 12
- 4-1 JW-20CM 14
- Set at delivery 15
- 4-2 JW-20RS 16
- Chapter 5 Installation 18
- ②③④ ⑤⑥ ⑦ 20
- (Ex.: JW-13BU) 20
- Control module 20
- Port number 20
- 2 rack panel max 21
- Phillips screwdriver 23
- Power supply module 23
- Module attachment 23
- The system consists of the 24
- Set the blade to within 25
- 1 mm in order not to 25
- When the adjustment 26
- KEDAADFS 27
- Chapter 7 Wiring 30
- 7-6 Check after wiring 34
- Chapter 8 Remote I/O 39
- × 8 points) 41
- Processing of JW-20CM 42
- Processing of PC side 42
- Hold time [ms] 45
- TerminatorTerminator 49
- Less than 1 km 49
- 1ledomWZfoeludomO/I 53
- 2ledomWJfoeludomO/I 53
- From the previous page 56
- Write in label 56
- (JW model or ZW model) 57
- O: Necessity for setting 57
- Operation procedure 58
- In brackets : See page 58
- Not setting dummy I/O 59
- HEX (hexadecimal) 60
- OCT (octal) 60
- DCM (decimal) 60
- Bit pattern 60
- Display on the JW-13PG 67
- (Light OFF) 67
- (8) = 00(H)) 69
- (8) = 81(H)) 69
- 17776 OCT 000 72
- 17777 OCT 000 72
- >00000 OCT 014 72
- 00000 0 005014 78
- 00002 0 000200 78
- >00004 0 101000 78
- 00200 DCM 000 80
- 00201 DCM 008 80
- >00202 DCM 010 80
- □□□□□□□□ 81
- □■■■■■■■ 81
- 76543210 0 0 83
- (8) etc 83
- 8-4 Error and treatment 84
- ② JW-20RS 86
- Indication lamp 86
- All stations 89
- Slave station 77(8) 89
- Chapter 9 Data Link 99
- 9-2 Communication method 100
- Target station 106
- 64 bytes 107
- 00000 F–44 02030 02000 112
- 02000 02030 112
- 9-4 Expansion of network 113
- : Master station 114
- : Slave station 114
- Terminator: ME-75 117
- Coaxial cable 118
- Turn “ON” shield ground 118
- Corresponding 120
- 11·7 and 11·8 120
- When not using 121
- SEND/RECEIVE function 121
- When not using memory 121
- Screen display of JW-13PG 122
- Setting 125
- 07714 D 00000 126
- 07716 D 00000 126
- I PARAM 126
- >07720 D 00004 126
- 07726 0 000000 127
- 07730 0 001000 127
- >07732 0 000000 127
- HAM1-WJ,AM1-WZ1ro0 ※ 128
- HAM2-WJ,AM2-WZ1ro0 128
- HAM3-WJ,AM3-WZ2,1,0 128
- HAM4-WJ,AM4-WZ7,6,5,4,3,2,1,0 128
- Contents 130
- bytes bytes bytes 133
- 24 24 24 134
- →Bit pattern 137
- After converting to octal 138
- (4 bytes) 139
- 004004(8) 140
- 004010 to 004011(8) 141
- File number of communication 148
- File number 149
- 9-8 Error and treatment 151
- (2) Flag 153
- Communication monitor 158
- 76543210 160
- Port 7 error 160
- Port 5 error Port 3 error 160
- Chapter 10 Computer link 169
- 10-2 Communication method 170
- 10-3 Switch setting 171
- 10-4 Command 172
- CPfonoitidnocnoitarepO ataD 179
- )FFO(000 182
- Chapter 11 Support Tools 188
- 11-2 Remote function 192
- Satellite net 193
- (JW-50PG) 194
- Chapter 12 Specifications 198
- 12-2 JW-20RS 201
- Chapter 13 Appendix 202
- 13-2 Switch setting table 203
- 13-3 Parameter memory table 204
- (8) are all 00(H) 205
- (8) Set contents 206
- (8) I/Os are JW models 208
- (8) are all 91(H) 215
- Bit address 76543210 216
- ③ Data link slave station 217
- Slot: 1 Slot: 0 220
- (File 0) 221
- HAM4-WJ,AM4-WZ7,6,5,4,3,2,2,0 222
- Top address for 223
- Completed receiving flag 225
- Power module 227
- Port No 227
- Send Data 228
- Receive Data 229
- Target Station 230
© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales