Sharp AN-LS1 Especificaciones

IntroductionConnectionsSetupUsing the SoftwareAppendixMODEL AN-LS1OPERATION MANUALEthernet to RS-232C Network Converter• Please read this operation ma

10Connecting the AC AdaptorTake the following steps to connect AN-LS1’s AC adaptor.1 Plug the AC adaptor’s DC plug into AN-LS1’s DC IN jack.2 Plug the

11SetupEntering SETUP MENUConnect AN-LS1 to a computer using RS-232C or Telnet, and open the “SETUP MENU” on the computerto carry out various settings

12When Connecting Using Telnet1 Click “Start” from the Windows desktop and select “Run”.2 Enter “telnet 192.168.150.2” in the text box that opens up.(

13SetupSETUP MENU DescriptionSETUP MENU (Main Menu)S E T U P M E N U[1]IP Address [2]Subnet Mask [3]Default Gateway[4]User Name [5]Password[6]RS-23

14ADVANCED SETUP MENU******************** ADVANCED SETUP MENU ***********************[1]Auto Logout Time [2]COM Redirect Port [3]Busy Reply[4]Input

15SetupBasic ProcedureEnter number or symbol of item to be selected on the “SETUP MENU”. When setting, input the detailsto be set. Setting is carried

16Set Items(e.g.) When setting IP Address (change from 192.168.150.2 to 192.168.150.3)▼ The SETUP MENU———————— S E T U P M E N U ——————————[1]IP Ad

17SetupQuitSave settings and quit. ([S]Save & Quit)Save set values and quit menu.▼ The SETUP MENU———————— S E T U P M E N U ——————————[1]IP Add

18Setting of Each ItemThe setting procedure for each item will be explained. For the basic procedure, please refer to page15.IP Address Setting ([1]IP

19SetupUser Name Setting ([4]User Name)Carrying out security protection using user name.setup>4User Name :Please Enter : an-ls1(change) —>

2Outstanding FeaturesAN-LS1 is a network converter for converting TCP/IP protocol on Ethernet to serial (RS-232C). AN-LS1 enables Sharp projectors wi

20Unit Name Setting ([7]Unit Name)It is possible to assign a unit name.When searching using Sharp COM Redirection Software, it is possible to verify a

21SetupThe followings are descriptions of the ADVANCED SETUP MENU.Setting Automatic Logout Time (ADVANCED[1]Auto Logout Time)If there is no input afte

22Busy Reply Setting (ADVANCED[3]Busy Reply)The input terminals of AN-LS1 can be RS-232C (CONTROLLER) and 10BASE-T. Respective inputterminals can be c

23SetupCarrying out Network Ping Test (ADVANCED[5]Network Ping Test)It is possible to confirm that a network connection between AN-LS1 and a computer

24Setting of Port for Search (ADVANCED[0]Port for Search)Sets the port number used when Sharp COM Redirection Software searches for AN-LS1.advanced>

25Using the SoftwareAbout Sharp COM Redirection SoftwareUsing Sharp COM Redirection Software, it is possible to create a “Virtual COM” port. If genera

26InstallationThe Sharp COM Redirection software (Virtual COM Driver software) is installed using the installationprogram provided on the CD-ROM.This

27Using the Software• Please change the destination only when necessary. (In general, it is not necessary to changethe destination folder.)• If “Cance

286 Enter a check mark against Virtual COMs to be added to the computer and click“OK”.• It is necessary to add the same number of Virtual COMs as the

29Using the SoftwareStartingLaunch Sharp COM Redirection Software.1 Launch by double clicking the Sharp COM Redirection Software icon in the ControlPa

3IntroductionContentsIntroductionOutstanding Features ...

30Explanation of the Screen▼ Configuration dialog89214 5 6731 List display areaList display of states of all units recognizing Sharp COM Redirection S

31Using the SoftwareOperationsSearch and AddSearches for units on a network and adds to the list display.1 Click “Search”.| “Search tool” dialog is di

322 Click the unit to be added to list display.3 Click “Add to List”.| Added to list display after carrying out communication to each selected unit.

33Using the SoftwareSelecting Virtual COM PortSelecting Virtual COM port used when communicating with AN-LS1.1 Click the “Virtual COM” column.| The “V

342 Click and select the “Virtual COM” number to be used for communication with AN-LS1.3 Click on an area outside the “Virtual COM” pull down menu.| “

35Using the SoftwareAdd (Manual)Adding units to the list display manually in cases such as when units cannot be found, even by searching.1 Click “Add”

362 Enter IP address and click “OK”.| Unit will be added.

37Using the SoftwareRefreshChanging the list display content to the latest state.1 Click “Refresh”.| Model Name, Unit Name and Status will be updated

38DeleteDeleting an unit from the list display.1 Click on the unit to be deleted.2 Click “Delete”.

39Using the Software| A confirmation dialog will be displayed.• If you do not want to delete the unit, click “Cancel”.3 Click “Yes”.| The unit to be d

4Part Names and FunctionsMain BodyTX/RX LED indicator (Page 5)Lit when transmitting data.10BASE-T Ethernet terminal (Page 8)To connect to an Ethernet

40PasswordIf units with user name/password set appear within the list display, the user name/password for thoseunits must be entered.Enter when commun

41Using the Software2 Click “Password”.| A dialog prompting entry of user name/password will be displayed.3 Enter the user name and password being set

42SettingSetting of computer data communication port number and search port number.1 Click “Setting”.| “Setting” dialog will be displayed.2 Enter “Sea

43Using the SoftwareOK/CancelWhen defining content of setting or change, click “OK” when closing the “Configuration dialog”.When canceling content of

44Changing / Removing the SoftwareBe sure to always uninstall the Sharp COM Redirection Software, when reinstalling the Sharp COMRedirection Software

45Using the Software5 Select “Modify”, “Repair” or “Remove”, and then click “Next>” on the “Welcome”dialog box. “Modify”For adding or removing Virt

46Connecting Pin AssignmentsRS-232C Terminal: 9-pin D-sub male connectorPin No. Signal Name I/O Reference1 CD Not connected2 RD Receive Data Input Con

47AppendixTroubleshootingThe POWER indicator on the top panel does not light green.\ Check if the power plug of the AC adaptor is disconnected from th

48Check the network settings for the computer and AN-LS1.\ Check the following network settings for AN-LS1.• IP address\\ Check that the IP address fo

49AppendixC:\>ipconfig “RETURN”Usage examples of ipconfigC:\>ipconfig /? displays how to use “ipconfig.exe”.C:\>ipconfig displays the set IP

5IntroductionLED IndicatorsThe LED indicators at the side and on the top of AN-LS1 represent the contents in the followingtable.POWERLINKTX/RXName LED

50\ Check if the “TCP/IP” protocol is operating correctly using the “PING” command. Also, check if anIP address is set.1. Open a command prompt (MS-DO

51AppendixSharp COM Redirection Software does not operate.AN-LS1 cannot be found by a search.\ Check the connection. (Refer to “When connecting AN-LS1

52SpecificationsMain BodyDescription Ethernet to RS-232C Network ConverterInput voltage DC 6.3 V, 400 mAOperating temperature 41°F to 104°F (5°C to 40

53AppendixIndex10BASE-T Ethernet terminal ... 8AAccept All IP Addr... 23Accept IP A

SHARP CORPORATION

6Wall MountYou will find it convenient to mount AN-LS1 on the wall, using two screws, as indicated below.1 Screw two screws (not included) into the wa

7ConnectionsOverviewUse the following procedure for connection of AN-LS1.1 Connect AN-LS1 to an Ethernet LAN. (Page 8)2 Connect devices to AN-LS1. (Pa

8Connecting to an Ethernet LANConnect AN-LS1 to a hub or a computer using a Category 5 cable.• It is necessary to perform computer setting according t

9ConnectionsConnecting DevicesConnect a commercially available controller or computer and a projector to AN-LS1.Connecting a Controller or a ComputerI