
On-Screen Display Menu
Position
For
adjusting a picture's horizontal
and
vertical
position.
H-Pos.: Centers the image by
moving
it to the left or
right.
V-Pos.: Centers the image by
moving
it up or down.
• For resetting adjustments to the factory preset values, press
AI,.
to select "Reset", and then press ENTER.
• When connecting a PC to the HOMI terminal, the image
position will be automatically adjusted.
It
cannot be
manually adjusted.
• Adjustments are stored separately according to input
source.
• When a
OlV
channel is selected, the horizontal position
cannot be adjusted.
• The horizontal and/or vertical position may not be able
to
be adjusted
or
it may be adjusted only
to
a certain degree.
PC
Setup
Some
input signals
may
have
to
be
registered
manually
to
display
properly.
The
pair
of
input
signals
(resolutions)
in
the list below
is
not distinguishable
when
received.
In
such a
case,
you
have
to set the correct
signal
manually.
After setting
once,
it
will
display
when
the
same
signal
(resolution)
is
input
again.
11024 x768 1360 x 768 I
• You can only select the "Input Signal" on the Setup menu
when receiving one
of
the 2 input signals listed
above.
For
automatically adjusting the
PC
image.
Yes: Auto Sync. starts.
No: This function does not work.
• When Auto Sync. is successful, "Completed" displays.
If
not, Auto Sync. failed.
• Auto Sync. may fail
even
if "Completed" displays.
• Auto Sync. may fail if the computer image has low
resolution, has unclear (black) edges, or is
moved
while
executing Auto Sync.
• Be sure
to
connect the PC
to
the
lV
and switch it on before
starting Auto Sync.
21
Ordinarily
you
can
easily
adjust
the
picture
as
necessary to change
image
position
using
Auto
Sync.
In
some
cases,
however,
manual
adjustment
is
needed
to optimize
the
image.
H-Pos.: Centers the image by
moving
it to the left
or
right.
V-Pos.: centers the image by moving it
up
or
down.
Clock: Adjust when the image flickers with vertical
stripes.
Phase: Adjust when characters
have
low contrast
or
when the image flickers.
• For resetting
all
Fine Sync. adjustment items to the factory
preset values, press
AI,.
to
select "Reset", and then press
ENTER.
• It is not necessary
to
adjust the "Clock"
or
"Phase" when a
digital signal is being input, so it cannot be selected.
• The default cursor position may not be
in
the center,
because the screen position variable ranges may
be
asymmetrical.
PC
Audio Select
Determines whether
the
AUDIO
terminal
is
used for
INPUT
4
(PC-IN)
or
INPUT
5
(HDMI).
Input 4 (PC): Select this item when the audio signal is
input
via
the INPUT 4 (PC-IN) terminal using
an
analog
RGBcable.
Input 5 {HOMI): Select this item when the audio signal is
input
via
the INPUT 5
(HOMI)
terminal using an HOMI-
OVI
conversion cable.
• When "PC Audio Select" is set to "Input 5 (HOM!)", sound
will not be produced if you use only an HOMI-certified
cable to connect HOMI-compatible equipment. To produce
sound, you should make an analog audio connection.
• If you want to connect HOMI-compatible equipment using
only an HOMI-certified cable, set "PC Audio Select"
to
"Input 4 (PC)".
HDMI Auto View
To watch
an
HDMI
or
PC-IN
equipment
image,
select
"INPUT5",
"INPUT6"
or "INPUTl" from
"INPUT
SOURCE"
menu
using
INPUT
on
the
remote control
unit or
on
the
lV.
Enable: To use View Mode based on signal recognition,
including an HOMI signal.
Disable:
No
function.
• Refer to your external equipment operation manual for the
signal type.
• When connecting an HOMI-OVI conversion adapterlcable
to
the HOMI terminal, the image may not come in clearly.
Comentarios a estos manuales