Sharp SF-2014 Manual de servicio Pagina 23
- Pagina / 128
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
(2) Remove the paper tray from the main copier
unit.
1 While lifting up slightly, gently pull out on the paper tray until it
stops.
2 Then, lift up on the paer tray with both hands and remove it.
(3) Open the upper unit of the main copier unit.
1 Press the release buttons on the left and right sides of the main
copier unit’s front cover, then open the front cover.
2 Push the upper half release lever (green) to the right and down,
then gently open the upper unit.
(4) Connect the main copier unit and the paper
feed unit.
1 Secure mounting screw A (1 pc) in the main copier unit (1 loca-
tion).
Then, gently close the upper unit and front cover.
2 Connect the paper feed unit and the main copier unit by securing
mounting screw B (2 pcs) in the mounting holes (2 locations)
located in the slot from which the paper tray was removed.
*
After these procedures have been completed, reload the paper
tray which was removed in step 2.
3 Insert the paper feed unit connector into the jack on the side of the
main copier unit.
Front cover release buttons
Front cover
Upper half
release lever
Upper unit
Mounting
screw A
Mounting screw B
Connector
4 – 7
- SERVICE MANUAL 1
- MODEL SF-2014 1
- MODEL SF-2214 1
- CONTENTS 2
- [1] GENERAL DESCRIPTION 4
- [2] PRODUCT SPECIFICATIONS 6
- • Inch series 7
- • Single 7
- • Developer 7
- • Toner 7
- 3. Supplies 8
- Upper unit 10
- Lower unit 10
- 1. Packing drawing 17
- 2. Installation 17
- (2) Space around the machine 18
- (3) Installing table 18
- Mirror unit fixing screw 19
- (3) Developer setting 20
- (4) Toner supply 20
- (6) Accessory attachment 21
- Installation Manual 22
- Mounting 23
- [5] GENERAL DESCRIPTIONS OF 25
- EACH SECTION 25
- 3. Fuser, paper exit section 26
- 4. Developer section 26
- 5. Optical system 27
- 5-2. Basic operations 28
- 6. Copy process 30
- (3) Actual process 31
- OPC drum 32
- Step 5 (Development) 33
- Step 6 (Transfer) 34
- Step 7 (Separation) 34
- Aluminum layer 35
- (5) Process correction system 36
- 2) Correction operation 36
- [Initial setting] 37
- [Correction timing] 37
- [Correction operation] 37
- 7. SPF section (SF-2214 only) 38
- [6] DISASSEMBLY AND ASSEMBLY 40
- 1-3. Separation roller 41
- One-way clutch side 42
- 1-6. Transport belt 43
- 1-7. Socket holder unit 43
- 1-8. Lower unit PWB 43
- 1-10. Power unit 43
- Arrow mark 44
- 3. Fuser section 45
- Paper exit paper guide 47
- 4. Optical system 48
- <Removal> 49
- <Installation> 49
- 4-6. Optical unit removal 50
- 5. SPF section 52
- 1 , 2 ." 53
- 5-5. Clutch/solenoid removal 54
- 5-6. Sensor removal 54
- 6. Drum section 55
- 7. Developer section 55
- 7-3. Toner motor removal 56
- 7-4. Toner density sensor 56
- 9-1. Ozone filter 57
- 9-3. Ventilation fan motor 57
- 9-4. Transport roller clutch 58
- 9-5. Paper exit sensor 58
- [7] ADJUSTMENTS 59
- 0.6±0.03mm 60
- 2. Optical section 61
- Document Copy 64
- Document Copy A Copy B 65
- Optical unit cover 66
- Scanner unit drive pulley 67
- Set screw 67
- No.2 scanner unit 68
- Positioning plate 68
- Do not move 68
- Document Copy C Copy D 69
- Change the right side 70
- Change the left side 70
- Copy paper 71
- No.4/5 mirror drive lever 72
- No.4/5 mirror unit frame 72
- Copy image size 74
- Original size 74
- (7) Uniformity adjustment 76
- Paper exit 77
- Half-tone copy 77
- Less exposure 77
- (Dark copy) 77
- Scale image lead edge 79
- Reduction copy (x 0.64) 79
- 10 20 30 80
- Copy scale image 81
- Paper lead edge 81
- 3. COPY DENSITY ADJUSTMENT 84
- Not copied 85
- Slightly copied 85
- adjustment 86
- 4. Others 88
- Cut the wire at the 88
- Wind two turns and 88
- [8] SIMULATIONS 89
- 4. Purpose list 90
- 5. Details of simulations 91
- ÷ Document length x 100 [%] 95
- EXP1~5 voltage 99
- Full power 99
- 6. User simulation 101
- [9] SELF DIAG 102
- 4. Self diag contents 103
- 2) Transport section 108
- 1) Paper feed section 108
- [10] SERVICING AT MEMORY 109
- TROUBLE AND MAIN 109
- CONTROL PWB REPLACEMENT 109
- 4. Set value recording sheet 112
- 5. Memory simulation list 113
- [11] MAINTENANCE 114
- [12] ELECTRICAL SECTION 115
- 3. Main circuit 116
- 3 Block diagram 117
- IN XIN IN Clock IN 118
- OUT XOUT OUT Clock OUT 118
- H=+32V, VB=+24V 119
- 1 General 120
- Stepping motor time chart 121
- External view 5P5 122
- Delay capacity 122
- (1) Outline 125
- (2) Display circuit 126
- 1 Block diagram 126
- 2 Operation 126
- (3) LED display 127
- • AC PWB unit 127
- • In the main PWB unit 128
Relacionado con productos y manuales para Impresión y escaneo Sharp SF-2014
Impresión y escaneo Sharp AR-M300 Manual de usuario
(13 paginas)
(13 paginas)
Impresión y escaneo Sharp AR-M280 Manual de usuario
(11 paginas)
(11 paginas)
Impresión y escaneo Sharp AR-RB1 Manual de usuario
(59 paginas)
(59 paginas)
Impresión y escaneo Sharp AR-D20 Manual de usuario
(32 paginas)
(32 paginas)
Impresión y escaneo Sharp AR-M351U Manual de servicio
(276 paginas)
(276 paginas)
(2 paginas)
Impresión y escaneo Sharp arm455nb Manual de usuario
(73 paginas)
(73 paginas)
Impresión y escaneo Sharp JX-9400 Información técnica
(211 paginas)
(211 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.086 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales