Sharp TL-M5200 Especificaciones

MODELTL-M5200TL-M4600LCD MONITORRS-232C Specifications and Commands ... 2Setting up the Monitor Network Environment ...101. Connecting the Mon

-10Page 111. Connecting the monitor to a computerSetting up the Monitor Network EnvironmentThis section describes the basic procedure for using the mo

-11Setting up the Monitor Network Environment1. Connecting the Moni-tor to a ComputerEstablishing a one-to-one connection from themonitor to a compute

-12121XXXXXXXXX12Setting up the Monitor Network Environment2. Setting an IP Addressfor the ComputerThe following describes how to make settingsin Wind

-13Setting up the Monitor Network Environment125 Click “Internet Protocol Version4 (TCP/IPv4)”, and click the“Properties” button.6 Confirm or change a

-14Setting up the Monitor Network Environment3. Setting up a NetworkConnection for theMonitorSettings for such items as the monitor’s IP ad-dress and

-154 The TCP/IP setting screen ap-pears, ready for network settingsfor the monitor.Note• Confirm the existing network’s segment (IPaddress group) to a

-16Controlling the Monitor via LANControlling the MonitorUsing Internet Explorer(Version 5.0 or later)Complete connections to external equipmentbefore

-17Confirming the MonitorStatus (Status)On this screen, you can confirm the monitorstatus. You can confirm the following items :••••• MAC Address•••••

-18Controlling the Monitor via LANSetting and Adjusting theMonitor (Settings & Adjustments)Example: “Picture” screen display for COMPUTEROn these

-19Controlling the Monitor via LANMaking General Settingsfor the Network (Network –General)On this screen, you can make general settingsrelating to th

-2Computer controlA computer can be used to control the monitor by connecting an RS-232C serial control cable (cross type,commercially available) to t

-20Controlling the Monitor via LANSetting Error Items andDestination Addresses towhich E-mail is to be Sentwhen an Error Occurs(Mail – Recipient Setti

-21Setting up the Monitor Using RS-232C or TelnetWhen Connecting UsingRS-232C1 Launch general purpose terminalemulator.2 Input settings for the RS-232

-22When Connecting UsingTelnet1 Click “Start” from the Windows® desk-top and select “Run”.2 Enter “telnet 192.168.150.2” in the textbox that opens up.

-23SETUP MENU (Main Menu)[1]IP AddressIP address settings. (Page 26)[2]Subnet MaskSubnet mask settings. (Page 26)[3]Default GatewayDefault gateway set

-24View Setting Detail List([V]View All Setting)11111 Enter “v” and press the “Enter” key.Display all setting values(*).Enter number or symbol of item

-25Save Settings and Quit([S]Save & Quit)Save set values and quit menu.11111 Enter “s” and press the “Enter” key.22222 Enter “y” and press the “En

-26IP Address Setting([1]IP Address)Setting of IP address.11111 Enter “1” and press the “Enter” key.22222 Enter numerical value to be set and press th

-27Password Setting([5]Password)Carrying out security protection using password.11111 Enter “5” and press the “Enter” key.22222 Enter password and pre

-28Disconnecting All Connec-tions ([D]Disconnect All)It is possible to disconnect all the TCP/IP connec-tions currently recognized by the monitor. Eve

-29Carrying out Network PingTest(ADVANCED[5]Network Ping Test)It is possible to confirm that a network connectionbetween the monitor and a computer et

-3CommandsExample: When turning on the monitor, make the following setting.→←POWR _ 1__ OKMonitorComputerNormal(Computer)FullDot By Dot(Computer) /Nor

-30Setting of Search Port(ADVANCED[0]Search Port)Sets the port number used when searching for themonitor from the network.11111 Enter “0” and press th

-31Multi ScreenInfo• Before setting up the multi screen, install Internet Explorer (version 5.0 or later).• Image quality may deteriorate when picture

-32Multi ScreenSetting up the Multi Screen Input SignalFollowing is an example of how to use 4 monitors.Video equipmentMonitor 1ComputerComputerRGB c

-33Multi Screen1 Access one of the four monitors viaInternet Explorer.(See “Controlling the Monitor Using InternetExplorer (Version 5.0 or later)” (pa

-34Multi ScreenNotes on the Wide Multi ScreenSelecting “2 X 1”, “3 X 1”or “4 X 1” on “Status” (see page 33) allows you to create the wide multi screen

-35Multi ScreenSetting up the Multi Screen ControllingWhen you want to control the monitors collectively for the multi screen, connect LAN cables to

-36Multi Screen1 Change the TCP/IP settings for thecomputer as shown below.(See “Setting an IP Address for the Computer”on page 12 for the details.)•

-37Multi Screen4 Turn on all of the monitors.5 Access the monitor 1 from the com-puter via Internet Explorer.(See “Controlling the Monitor Using Inter

-38Multi ScreenMasterSet InputsONONOFFOFFOFFONONOFFOFFOFFOFFONCOMPUTER 1COMPUTER 2DVIHDMIVIDEOS-VIDEOSlaveSet InputsCOMPUTER 1COMPUTER 2DVIHDMIVIDEOS-

-39Communication cannot be established with the monitorWhen connecting the monitor using serial-connection\ Check that the RS-232C terminal of the mon

-4RS-232C Specifications and CommandsNormal (Computer)FullDot By Dot(Computer) /Normal(Video)S.Stretch(Video)Cinema16:9(Video)Cinema14:9(Video)Zoom14:

-40Troubleshooting\ Take the following steps for checking the network settings for the computer.1. Open a command prompt.• In the case of Windows® 200

-41\ Check if the “TCP/IP” protocol is operating correctly using the “PING” command. Also, checkif an IP address is set.1. Open a command prompt.• In

-5RS-232C Specifications and CommandsStandardPresentationMovieGamesRGBOff On On(Display)-16 – +160 – +40-30 – +30-30 – +30 -30 – +30-10 – +1

-6RS-232C Specifications and CommandsCONTROL CONTENTSPower ONStandby mode(Mode 1, Mode 2)COMMANDPARAMETERRETURNHDMI INPUTS-VIDEO INPUTAV ModeOPCBackli

-7RS-232C Specifications and CommandsCONTROL CONTENTSPower ONStandby mode(Mode 1, Mode 2)COMMANDPARAMETERRETURNVIDEO INPUTPositionFine SyncRGB Frequen

-8RS-232C Specifications and CommandsCONTROL CONTENTSPower ONStandby mode(Mode 1, Mode 2)COMMANDPARAMETERRETURNVideo SystemBackground SelectionLEDPowe

-9RS-232C Specifications and CommandsCONTROL CONTENTSPower ONStandby mode(Mode 1, Mode 2)COMMANDPARAMETERRETURNP&P Main SelectALL ResetSleep Timer