Sharp DX-C400 - Color - All-in-One Especificaciones Pagina 1

INSTALLATION REQUIREMENTSSUPPLIESSPECIFICATIONSINFORMATION ON DISPOSALTO THE ADMINISTRATOR OF THE MACHINEREPLACING SUPPLIES ANDMAINTENANCEDIGITAL FULL

8INSTALLATION REQUIREMENTSImproper installation may damage this product. Please note the following during initial installation and whenever the machin

9INSTALLATION REQUIREMENTSCAUTION:Do not install the machine in a location with poor air circulation.A small amount of ozone is created inside the mac

10SUPPLIESStandard supplies for this product that can be replaced by the user include paper, toner cartridges, and staple cartridges for the finisher.

11REPLACING SUPPLIES AND MAINTENANCEThis section explains the procedures for replacing supplies such as toner and staple cartridges and routine mainte

12REPLACING SUPPLIES AND MAINTENANCE1Open the front cover.Locations of colour toner cartridges2Pull the toner cartridge toward you.Example: Replacing

13REPLACING SUPPLIES AND MAINTENANCE3Take out the new toner cartridge, hold it with both hands, and shake 5 or 6 times horizontally.• When shaking the

14REPLACING SUPPLIES AND MAINTENANCE5Insert the new toner cartridge horizontally and push it firmly in.The shape of the toner cartridge varies by colo

15REPLACING SUPPLIES AND MAINTENANCE6Close the front cover.• After the toner cartridge is replaced, the machine automatically enters image adjustment

16REPLACING SUPPLIES AND MAINTENANCEReplacing the toner collection containerThe toner collection container collects excess toner that is produced duri

17REPLACING SUPPLIES AND MAINTENANCE3Remove the toner collection container.• If the toner collection container is tipped forward too far, it will not

Each instruction also covers the optional units used with these products.Caution!For complete electrical disconnection, pull out the main plug.The soc

18REPLACING SUPPLIES AND MAINTENANCE5Turn the lock lever on the toner collection container to the left.Turn the lock lever to the left until it stops.

19REPLACING SUPPLIES AND MAINTENANCEReplacing the developer cartridge / drum cartridgeBefore replacing the developer cartridge or drum cartridge, turn

20REPLACING SUPPLIES AND MAINTENANCE3Open the main charger cover.(1) Turn the main charger cover lock levers in the direction of an arrow below.When t

21REPLACING SUPPLIES AND MAINTENANCE4Remove the developer cartridge.(1) Grasp the developer cartridge lock and pull it forward and down.(2) Squeeze th

22REPLACING SUPPLIES AND MAINTENANCE5Shake the new developer cartridge 5 or 6 times as shown.Hold the developer cartridge firmly as shown below and sh

23REPLACING SUPPLIES AND MAINTENANCE6Insert the new developer cartridge horizontally.Insert the new developer cartridge in the same location as the ca

24REPLACING SUPPLIES AND MAINTENANCE8Hold the developer cartridge with one hand and slowly remove the seal with the other hand.Slowly pull the seal st

25REPLACING SUPPLIES AND MAINTENANCE10Install the toner collection container.☞ Replacing the toner collection container (page 16)11Close the front cov

26REPLACING SUPPLIES AND MAINTENANCE12Turn on the power.Switch the main power switch "ON" and press the [POWER] key ( ) on the operation pan

27REPLACING SUPPLIES AND MAINTENANCEReplacing the drum cartridgeYour service technician will replace the drum cartridge. Only replace the cartridge as

1EMC (this machine and peripheral devices)For the users of the fax functionFAX interface cable and Line cable:These special accessories must be used w

28REPLACING SUPPLIES AND MAINTENANCE3Remove the protective material from the drum cartridge and slowly insert the drum cartridge along the guides.Make

29REPLACING SUPPLIES AND MAINTENANCEReplacing the staple cartridge in the finisherWhen the staple cartridge runs out of staples, a message will appear

30REPLACING SUPPLIES AND MAINTENANCE4Remove the empty staple cartridge from the staple case.Gently grasp the right side of the staple cartridge as sho

31REPLACING SUPPLIES AND MAINTENANCE6Replace the staple case.Push the staple case in until it clicks into place.7Slide the finisher back to the right.

32REPLACING SUPPLIES AND MAINTENANCERegular maintenanceTo ensure that the machine continues to provide top quality performance, periodically clean the

33REPLACING SUPPLIES AND MAINTENANCEScanning areaIf coloured lines or white lines appear in images scanned using the automatic document feeder, clean

34REPLACING SUPPLIES AND MAINTENANCE3Release the lock levers and open the main charger cover.☞ Replacing the developer cartridge (page 19)4Remove the

35REPLACING SUPPLIES AND MAINTENANCE5Clean the main charger.(1) Gently push the charger cleaner all the way in.(2) Gently pull the charger cleaner out

36REPLACING SUPPLIES AND MAINTENANCE6Repeat step 5 with each of the other main chargers.There are a total of 4 places to be cleaned in the machine as

37REPLACING SUPPLIES AND MAINTENANCE9Install the toner collection container.☞ Replacing the toner collection container (page 16)10Close the front cove

2ContentsTO ENSURE SAFE USE OF THE MACHINE . . . . . . . . . . . . . . . . . . 4Cautions . . . . . . . . . . . . . . . . . . . 4Warnings . . . . .

38REPLACING SUPPLIES AND MAINTENANCECleaning the bypass tray rollersIf you find that paper fed from the bypass tray misfeeds or is soiled by the rolle

39REPLACING SUPPLIES AND MAINTENANCE3To clean the rollers, wipe the roller with a clean cloth.CautionWhen cleaning the rollers, be careful not to inju

40REPLACING SUPPLIES AND MAINTENANCE5Turn on the power.Switch the main power switch "ON" and press the [POWER] key ( ) on the operation pane

41REPLACING SUPPLIES AND MAINTENANCECleaning the automatic document feeder rollersIf you find that originals fed through the automatic document feeder

42REPLACING SUPPLIES AND MAINTENANCE3To clean the rollers, wipe each roller with a clean cloth.CautionWhen cleaning the rollers, be careful not to inj

43REPLACING SUPPLIES AND MAINTENANCE5Turn on the power.Switch the main power switch "ON" and press the [POWER] key ( ) on the operation pane

44REPLACING SUPPLIES AND MAINTENANCECleaning the laser unitWhen the laser unit inside the machine becomes dirty, line patterns (coloured lines) may fo

45REPLACING SUPPLIES AND MAINTENANCE2Open the front cover and remove the toner collection container.☞ Replacing the toner collection container (page 1

46REPLACING SUPPLIES AND MAINTENANCE4Make sure that the cleaner at the tip of the cleaning tool is not dirty.If the cleaner is dirty, remove the clean

47REPLACING SUPPLIES AND MAINTENANCE6Remove the dirty cleaner.Firmly grasp the tool close to where the cleaner is attached.Use your other hand to pres

3The products that meet the ENERGY STAR® guidelines carry the logo shown above.The products without the logo may not meet the ENERGY STAR® guideline

48REPLACING SUPPLIES AND MAINTENANCE8Clean the laser unit.(1) Point the cleaner down and slowly insert the tool into the hole that you wish to clean.T

49REPLACING SUPPLIES AND MAINTENANCE9Repeat step 8 to clean all holes in the laser unit.There are a total of 4 holes to be cleaned in the laser unit.I

50REPLACING SUPPLIES AND MAINTENANCE12Close the front cover.Take care that your fingers are not pinched when closing the cover.13Turn on the power.Swi

51REPLACING SUPPLIES AND MAINTENANCECleaning the PT charger of the primary transfer belt unitIf black or coloured lines still remain after the documen

52REPLACING SUPPLIES AND MAINTENANCE3Clean the PT charger.(1) Slowly pull the PT charger cleaner out until you feel a slight resistance.(2) Slowly pus

53REPLACING SUPPLIES AND MAINTENANCE5Close the front cover.Take care that your fingers are not pinched when closing the cover.6Turn on the power.Switc

54SPECIFICATIONSMachine specifications / copier specificationsNameDigital Full Colour Multifunctional System MX-C310/MX-C311/MX-C380/MX-C381/MX-C400Ty

55SPECIFICATIONSMachine specifications / copier specifications (Continued)Warm-up time90 seconds or less(This may vary depending on the ambient condit

56SPECIFICATIONSMachine specifications / copier specifications (Continued)Bypass trayPaper sizes: A4, B5, A5, 8-1/2" x 14", 8-1/2" x 13

57SPECIFICATIONSMachine specifications / copier specifications (Continued)* Type A connectors are located on the front and back right of the machine (

4TO ENSURE SAFE USE OF THE MACHINECautions• Do not make any modifications to this machine. Doing so may result in personal injury or damage to the mac

58SPECIFICATIONSContinuous copying speeds** Copy speed during output of the second copy and following copies when performing continuous one-sided copy

59SPECIFICATIONSAcoustic noise emission (measurement according to ISO7779)ModelMX-C310/MX-C311MX-C380/MX-C381MX-C400Sound power level LwA Printing mod

60SPECIFICATIONSAutomatic document feeder specifications* Scanning in mono 2 mode of one side only is possible in fax and scan send modes.Original siz

61SPECIFICATIONSBusiness card feeder specifications* Device may be unable to correctly feed and scan the business card depending on the business card&

62SPECIFICATIONS500-sheet paper feed unit specifications* Only MX-CSX1 can be used.ModelMX-CSX1 (tray 2) MX-CSX2 (tray 3, tray 4)Paper sizesA4, B5, A5

63SPECIFICATIONSFinisher specificationsModelMX-FN12Paper sizesA4, B5, A5, 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5&quo

64SPECIFICATIONSFinisher specifications (Continued)*1 The maximum number of sheets that can be held varies depending on ambient conditions in the inst

65SPECIFICATIONSPrinter specifications*1 When the machine is used as a PostScript printer. (When MX-C310/MX-C380/ MX-C400 are used, the PS3 expansion

66SPECIFICATIONSNetwork scanner / Internet Fax*1 specifications*1 Internet fax expansion kit is required.*2 Total number of all destinations (Scan to

67SPECIFICATIONSPull scan function (TWAIN) specificationsSupported protocolTCP/IP (IPv4)Supported client PC operating systemsWindows 98 / Me / 2000 /

5TO ENSURE SAFE USE OF THE MACHINEWarnings• Do not touch the transfer belt and the transfer roller. Scratches or smudges on the transfer belt or trans

68SPECIFICATIONSFacsimile specificationsModelMX-FXX3Applicable telephone linePublic switched telephone network, PBXScanning resolution(supports ITU-T

69SPECIFICATIONSFacsimile specifications (Contimued)*1 Transmission speed is for an A4 or 8-1/2" x 11" document with approximately 700 chara

70INFORMATION ON DISPOSALA. Information on Disposal for Users (private households)1. In the European UnionAttention: If you want to dispose of this eq

71Information that the administrator of the machine requires is printed on the back of this page.(Separate this page from the manual and keep it in a

72TO THE ADMINISTRATOR OF THE MACHINE(Separate this page from the manual and keep it in a safe place.)Factory default passwordsWhen accessing the syst

73TO THE ADMINISTRATOR OF THE MACHINEFor the users of the fax functionImportant safety instructions• If any of your telephone equipment is not operati

74TO THE ADMINISTRATOR OF THE MACHINETrademark acknowledgmentsThe following trademarks and registered trademarks are used in conjunction with the mach

SHARP ELECTRONICS (Europe) GmbHSonninstraße 3, D-20097 Hamburg

6TO ENSURE SAFE USE OF THE MACHINEThe machine includes the document filing function, which stores document image data on the machine's hard drive

Maintenance & Safety GuideMX-C310/MX-C311/MX-C380/MX-C381/MX-C400 Maintenance & Safety GuidePRINTED IN FRANCETINSE4108GHZ2

7TO ENSURE SAFE USE OF THE MACHINELaser informationWave length 790 nm ±10 nmPulse times(North America and Europe)4.1 µs ±4.1 ns /7 mmOutput power Max